Главная Каталог Лицензионное ПО AutodeskAutodesk Revit 2024 для Windows лицензионный ключ активации. Тени: В Autodesk Revit 2024 появилась новая функция создания теней, которая позволяет более точно моделировать и визуализировать пересечение объектов с источниками света.
Best 9 New Features in Revit 2024
Another new tool in Revit 2024 allows us to control the alignment of freeform rebar when placing along a path. In previous releases, the rebar would stay aligned to the path, but we can now align the rebar vertically if required. An example of this is shown below with the curved wall with a tapering base. In this example, the rebar is aligned vertically but still runs along the path. Analytical Modelling Updates Many of these updates happened in Revit 2023.
Lat year we saw the introduction of an independent analytical model that could be managed and controlled separately from the physical model. To strengthen this workflow, we have some new tools to help with the definition of the analytical model. We can now create curved panels. The curved panel is then created.
When defining the analytical model, previously you would need to manually associate this to its physical counterpart, but we now have a new assisted option. This is, of course, much more efficient and will eliminate mistakes. The physical or analytical model can both be used to build the counterpart automatically. For example, if the engineer has started to build the analysis model in Revit, the technician can then use Dynamo Player to create the physical model based on the analytical model properties.
Analytical Loads The loads in previous releases were split into two groups, we had hosted loads and non-hosted loads which could be point, line or area loads. The non hosted loads would not update and would have needed to be recreated when the analytical model updated. Also, point loads were exceedingly difficult to place in precise locations and had to be done in plan views with workplanes. The new loads in Revit 2024 are now simpler and are always hosted.
Each load type has distinct options to assist when placing the load onto the analytical element. For example, the below image shows a point load being placed, and you can place this on an end point or pick a position along the element. When working with loads, the scale can now be controlled via the Structural Settings dialog box. Here you can set the minimum and maximum load value and set the actual length of the arrows.
This is useful to visually check load magnitude. The loads can now also be controlled with view filters which enables parametric floor loading plans, something that many users have been doing with filled regions!
There are also opportunities to sweep profiles along the surface to create curbs, for example. Here is an in-place mass with a sloped edge.
The old building pad option only resulted in vertical edges. Here is an in-place mass creating a tunnel within the toposolid. This was not possible in previous versions of Revit. Cut geometry enhancement With the advent of the toposolid feature, there have been enhancements to what kind of elements can be used to cut other elements.
Because the toposolid is a solid, Revit does not know that other elements should automatically cut it. If you have foundation walls going below grade, for example, you now must use the Cut tool and select the wall and the toposolid to get the correct graphic results in a section. Link coordination model Revit can now link a large number of file formats stored in BIM 360 via a linked Coordination Model. These models are represented within Revit as lightweight geometry and can be easily navigated.
Sub-elements can be selected, and their properties are listed in the Properties palette. If you were paying close attention just now, you might have connected the dots that a Revit model can be linked in as a lightweight model. This might be helpful with specific consultant models. Here is the big news, with this new feature, not only can you link in a Revit model, but you can link different versions of Revit models!
For example, your Revit 2024 model can link in a Revit 2022 model without needing to upgrade the 2022 model. Enscape does not support this element type in Revit.
А сразу так нельзя было сделать? Но и здесь не без проблем — выемку делает, а насыпь нет. Так что ещё надо допиливать. Для меня так же важно что теперь при редактировании вершин отображаются горизонтали! Теперь хоть работать с топотелом можно. Добавили ещё возможность создавать топотела по Форме, как крыши и перекрытия ХЗ зачем , кнопку упростить топотело не тестировал продолжает ли он упрощать сам при создании по точкам , и переключение отображения сглаженного рельефа и «гранённого» 9. Редактор материалов Говорят ускорили отрисовку миниатюр, засекать и сравнивать не стал, ну может немного быстрее стало. И добавили возможность с шифтом выделить несколько материалов и скопом их удалить, при чистке проекта или семейства полезно.
Автоматическое соединение и блокировка стен при создании Добавили соответствующую галочку. Вроде да может быть полезно, но галочка не решает проблему автоматического присоединения торцов стен друг к другу эффект виден на картинке , а следовательно лучше в отдельном файле делать отделку. Периметр помещения Напоследок ещё одно очень полезное изменение.
Пример топоповерхности и строительной площадки до проекта Revit 2024. Чтобы преобразовать топоповерхность, выберите ее и выполните действия, показанные на рисунке 26. На шаге 2 выбирается тип семейства топоповерхностей, в котором может быть задано несколько характеристик поверхности. Рисунок 26. Шаги по преобразованию топоповерхности в топосолид. Топоповерхность не удаляется, так как это привело бы к удалению строительных площадок, которые необходимо воссоздать вручную. Поскольку инструмента для создания строительных площадок нет, Autodesk рекомендует создать набор массы на месте для разрезания топосолида, как показано на рисунке 27. Это дает гораздо больше возможностей, например, туннели и наклонные края. Самая большая проблема заключается в том, что рабочий процесс, на мой взгляд, не так интуитивно понятен обычному пользователю Revit. Рисунок 27. Предлагаемая замена для инструмента строительной площадки - пустоты в массе. Субрегионы автоматически преобразуются в подразделы. На рисунке 28 показаны различные настройки типа для этого нового элемента. Обратите внимание на две вещи. Во-первых, в основе топосолида лежит элемент пола. Во-вторых, настройки контура теперь задаются для каждого типа объекта, а не глобально. Рисунок 28. Свойства топосолида. Зная, что этот элемент по сути является усовершенствованным элементом пола, обратите внимание, что применение материалов немного странно. В примере, показанном на рисунке 27, мне пришлось выбрать материал Earth, чтобы материал и узор были земляными. Затем мне нужно было нарисовать на поверхности материал травы. Сложность рисования заключается в том, что поверхность состоит из нескольких граней, и для закрашивания всей поверхности требуется несколько резцов. Toposolid - рабочий процесс создания Топосолид создается аналогично элементу пола. Вы начинаете с наброска периметра определяемой поверхности, а затем завершаете режим создания. Затем выделяется топоповерхность и используется опция Добавить точки на ленте, настраивая значение смещения также на ленте. Дороги и пешеходные дорожки создаются с помощью инструмента Sub-Divide, расположенного на ленте при выборе топосолида. Этот инструмент аналогичен инструменту "Подрайон", когда замкнутая область определяется в пределах большого периметра топосолида. В результате получается сплошное выдавливание, которое прилегает к земле и может быть отрегулировано по вертикали. Однако высота подраздела не может быть отрицательной. Последнее изображение в этом разделе показывает, как пустота в массе может создать туннель в топосолиде. Это невозможно при использовании топоповерхности. Когда CAD-файл доступен, топосолид может быть сгенерирован из него, как и раньше. Рисунок 29. Создание топосолида. Рисунок 31. Массивная пустота, создающая туннель в toposolid. Общие координаты Хотя в использовании общих координат нет ничего нового, этот рабочий процесс будет таким же и в Revit 2024, даже при использовании нового элемента toposolid. Этот рабочий процесс также работает в проекте, размещенном в BIM 360. Рисунок 32. Рабочий процесс с общими координатами. Усовершенствование геометрии разреза С появлением toposolid были усовершенствованы элементы, которые можно использовать для разрезания других элементов. Поскольку toposolid является твердым телом, Revit не знает, что другие элементы должны автоматически разрезать его. Например, если у вас есть стены фундамента, уходящие ниже уровня земли, вам придется использовать инструмент "Вырезать" и выбрать стену и toposolid, чтобы получить правильные графические результаты в разрезе. Выравнивание деталей Инструмент "Выравнивание" теперь имеет возможность применить выравнивание ко всей поверхности. В примере ниже поверхность имеет подэлементы, примененные к наклонным участкам поверхности. Это может привести к тому, что рисунок поверхности не будет выровнен по всему элементу пола. Эта новая функция помогает в выравнивании, тогда как раньше она позволяла применять выравнивание только к выбранной грани.
What’s new in Revit 2024 | Revit Tips #19
Well, Autodesk Revit 2024 is already here. And while 2023 certainly is not "old & busted," 2024 is already making waves in the community for some of the cool, new features is has to show. Revit 2024 allows the Bending Detail types to have either Standard, Unfold or Offset. В Revit 2024 на борту новая версия Dynamo + обновленный Dynamo Player. Autodesk Revit 2024» Autodesk Revit 2024 представляет собой отдельное приложение, которое поддерживает рабочий процесс BIM от разработки концепции до строительства.
Revit 2024 design & rendering software
The most significant improvement in Revit 2024 is the new TopoSolid tool, which replaces the old TopoSurface tool. Autodesk officially released Autodesk Revit 2024 and the relatedfamily of Autodesk Building Solutions 2024 products. Тени: В Autodesk Revit 2024 появилась новая функция создания теней, которая позволяет более точно моделировать и визуализировать пересечение объектов с источниками света.
Прекращение действия лицензий Autodesk
Усовершенствованная производительность Autodesk Revit 2024 внесла значительные улучшения в производительность, что позволит пользователям работать более эффективно. Autodesk Revit 2024 — программа для проектирования и строительства зданий и сооружений. Autodesk Revit основан на технологии информационного моделирования сооружений и. В Revit 2024 есть несколько неархитектурных усовершенствований продукта, которые перечислены ниже.
Revit 2025: Новинки общие и архитектурные
Our team has been digging in to get an up-close look at the new Revit 2024 release. Here are the top features and updates we think are most exciting about the new version. Toposolids 2. Dark Theme 5. Add Multiple Views and Schedules 6. Resize All Schedule Rows 7. Color Book Browser 8. Search in Project Browser 9. Open Sheet Directly from Drawing Area 10. My Insights in Revit Home 11.
Enable Floor Based Element on Toposolid 12. New ribbon icons 14. But Revit 2024 has created Toposolids, which take advantage of all of the System Family capabilities. You can now add layers with thickness and materials - just like other system families. In addition to that, there are also new Contour Display options. One thing to note: right now you need to use voids to cut out sections of the Toposolids. There will hopefully be a new tool in the future to be able to handle cuts in Toposolids in a better way. Our team is certainly looking forward to being able to host families on toposolids.
One of the main benefits is the capability to link models from previous versions of Revit without upgrading them. This feature is very useful when collaborating with other stakeholders who are working with older model versions. Once you have linked Coordination Models, you can manage these files in the Coordination Model tab located in the Manage Links menu. As you can see in the example below, every surface of the floor has been aligned individually with the same pattern. To reset the pattern, you can use the Entire Surface again. This style can be described as a hybrid mode between Consistent Colors and Realistic. It will show textures like in the Realistic mode but without the global lights which sometimes can be a little buggy on floorplans. You can use the Texture style for presentation in 3D views, or floor planners, for example. However, Revit 2024 has introduced its own Color Book. This Color Book has premade colors of different sets that can be used for different materials, filled regions, etc. Not only do the Color Books feature a variety of pre-existing color sets, such as Pantone colors, but they have also expanded to include RAL colors. Furthermore, you are allowed to search for a color in the blank field below the Color Books dialog. In order to use this feature properly, you need to be very precise when typing your search terms into the blank field.
Interface adjustments are available in the options on the Colors panel. This more interactive feature, highlighting entries as you order, is handy for large projects with numerous views, sheets, schedules, and families in the project browser. These color books resemble the AutoCAD versions, incorporating RAL and Pantone color books, and offer the flexibility to craft personalized color books. This customization feature empowers users to establish a palette of custom colors tailored for specific applications like room color fills and filled region colors. This style falls between Consistent Colors and Realism. This makes it a lighter option than Realistic, allowing you to showcase materials with their respective images. This feature makes it much easier to keep track of revisions made throughout the project and which sheet they have been applied to. The revision cloud schedule can include fields not only from the clouds but also from the revisions, sheets, and views, thereby streamlining the management of sheets and revisions throughout the project. The ability to edit the fields directly in the schedule will also speed up the workflow. This was mainly because it needed more options and capabilities in other system families.
The suggested replacement for the building pad tool is an in-place mass void. Sub-regions are automatically converted to sub-divisions. Figure 28 shows the various type settings for this new element. Notice two things. First, the toposolid is fundamentally based on the floor element. Second, the contour settings are now set per object type rather than globally. Figure 28. Toposolid properties. Knowing that the element is essentially an enhanced floor element, note that apply materials is a little odd. Then I had to paint a grass material on the surface. The tricky part with painting is that the surface is made up of several facets and required several picks to paint the entire surface. Toposolid — Creation Workflow A toposolid is created similar to a floor element. You start by sketching the perimeter of the ground to be defined and then finish the creation mode. Next, you select the toposurface and use the Add Points option on the ribbon, adjusting the offset value also on the ribbon. Roads and walkways are created using the Sub-Divide tool found on the ribbon when a toposolid is selected. This is similar to the sub-region tool where an enclosed area is defined within the larger toposolid perimeter. The result is a solid extrusion which conforms to the ground and can be adjusted vertically. However, the sub-divide height cannot be negative. The last image in this section shows how a mass void can create a tunnel in the toposolid. This was not possible with a toposurface. When a CAD file is available, a toposolid can be generated from it as in the past. Figure 29. Creating a toposolid. Figure 30. Creating a sub-division. Figure 31. Mass void creating a tunnel in toposolid. Shared Coordinates While there is nothing new with shared coordinates, I wanted to share a link to my YouTube series on the topic Shared Coordinates in Revit that is easy to understand and covers many of the questions that often come up. This workflow will be the same in Revit 2024, even when using the new toposolid element. This workflow also works on a project hosted in BIM 360. Figure 32. The shared coordinates workflow. Cut Geometry Enhancement With the advent of the toposolid, there have been enhancements to what kind of elements can be used to cut other elements. Because the toposolid is a solid, Revit does not know that other elements should automatically cut it. If you have foundation walls going below grade, for example, you now have to use the Cut tool and select the wall and the toposolid to get the correct graphic results in a section. Pattern Alignment The Align tool now has an option to apply the alignment to the entire surface. In the example below, the surface has sub-elements applied to slope portions of the surface. This can result in the surface pattern not aligned across the entire floor element. This new feature helps with the new alignment, whereas earlier, it only allowed for the selected face option. Figure 33. The new Entire Surface option for Align. Figure 34. The pattern aligned over the entire surface. Other Disciplinary Enhancements Revit 2024 has several non-architectural product enhancements that are listed below. Be sure to check out the official Autodesk blog post for more details on them. Structural Enhanced point loads on panels Enhanced analytical loads.
Best 9 New Features in Revit 2024
Read about the new updates for Revit 2024 that addresses 25 quality issues improving functionality and stability. In conclusion, Revit 2024 brings a host of exciting new features and enhancements that improve usability, enhance visual representation, and streamline workflows. Explore nine of the new features in Revit 2024 in this overview by Revit expert, Dan Stine. Read about the new updates for Revit 2024 that addresses 25 quality issues improving functionality and stability. The release of Revit Software 2024 is intriguing, but the software may be evolving slower than the industry would prefer.
AutoCAD 2024 и Revit 2024
Подумаем, как с этим жить. Обойти ограничение несложно, даже не потребуются какие-то спец инструменты. Для начала надо запретить службе AdskLicensing выход в интернет. Для этого воспользуемся стандартной функцией Брандмауэра Windows. Найдите его через Пуск: Перейдите в Дополнительные параметры: Выберите Правила исходящего подключения — Создать правило — Для программы: Далее надо указать путь к файлу. Далее — надо сломать службу Autodesk Genuine Service.
You can also configure the amount of detail that is displayed within the bending detail. For example, you could simply show the segment length dimensions or recover all the dimensions and angles for each segment as well as hooks and linear dimensions. There are also a few options around the unfolding or offsetting of Bending Details. When you have shapes such as links that overlap it could be confusing when showing lengths and angles of the hooks. These 3 configurations are shown in the image below using a standard link. Currently, the Bending Details cannot be tagged but I am sure that Autodesk will add this functionality in future releases. The bending details could also become a solution for certain detailing conventions such as tick and tag in sectional views and the display of bars in plan. Bending Details in Schedules The Bending Details can also be used in schedules which is especially useful for non-standard shape codes. It is worth noting that you will only see the shape once the schedule is placed onto a sheet. Again, in many other regions and countries, shape codes are always shown in the schedule regardless. In the example below, Bending Details are shown in the bending schedule with the new auto size option for rows with images. In the above image, the segment names are displayed to reduce the amount of space required but you can also configure the Bending Details specifically for use within schedules. Here in the UK, it would only be necessary to show the bending sketch for non-standard shapes so it would be useful to see a feature where you could control which shape codes use the new Bending Detail and display on the schedule. Again, this is the first iteration, and I am sure we will see other additions to this new feature in future releases. We will now look at a feature that was released in Revit 2023. Whilst this is an amazingly simple tool it really makes a difference when working with rebar. In the example below we have a rebar set which is configured for the spacing and number of bars. If I add additional bars, they may end up on the wrong end of the rebar set. Another new tool in Revit 2024 allows us to control the alignment of freeform rebar when placing along a path. In previous releases, the rebar would stay aligned to the path, but we can now align the rebar vertically if required. An example of this is shown below with the curved wall with a tapering base. In this example, the rebar is aligned vertically but still runs along the path. Analytical Modelling Updates Many of these updates happened in Revit 2023.
Some of the tools should be recreated from scratch instead of getting patched. Nevertheless, Autodesk did a good job overall. This article covers the general and architectural features of Revit 2024. The new design includes redesigned icons for both light and dark themes, which aims to reduce screen glare and enhance the viewing experience. After using it, I prefer it. The Canvas Theme button on the View ribbon tab enables easy switching of the graphics window between light and dark without affecting the rest of the interface. Interface adjustments are available in the options on the Colors panel. This more interactive feature, highlighting entries as you order, is handy for large projects with numerous views, sheets, schedules, and families in the project browser. These color books resemble the AutoCAD versions, incorporating RAL and Pantone color books, and offer the flexibility to craft personalized color books. This customization feature empowers users to establish a palette of custom colors tailored for specific applications like room color fills and filled region colors.
In this example, we create a void shape for a parking driveway. You could also use the model in-place tool, but uh... Overall, this is probably for the best... In Revit 2024: Each toposolid type can have different kinds of topography contours. In the type properties of a toposolid, you need to click on Contour Display. You can decide to have a toposolid type with lots of contours. However, the contours are not visible when editing the points. And maybe you want a water toposolid without any contours. In this example, the toposolid is cut to accommodate the foundation wall and footing. The volume of the toposolid accurately reflects the substraction of the these elements. This can be use to create curbs. You cannot use this tool on subdivisions, or on very complex shapes. If someone from Autodesk is reading: please fix this! It would be great to place the slab edges on sub-division. Meanwhile, you can use the railings tool to create curbs. Since toposolids are similar to floors, you can switch the composition entirely and have lakes, concrete pads, and other site components while keeping the original topography points. Be careful, though. You can use them on the new toposolid category. In Revit 2024: You can use the same Graded Region tool on toposolid. These are quite helpful.
What's New in Revit 2024
На ленте можно изменить выравнивание текста для нескольких текстовых элементов одновременно. Выберите текстовые элементы. На вкладке «Изменить Текстовые примечания» нажмите значок, соответствующий требуемому варианту: «Выровнять по верху», «Выровнять по середине», «Выровнять по низу», «Выровнять по левому краю», «Выровнять по центру» или «Выровнять по правому краю». Предупреждения об удалении видов в общих моделях! Чтобы избежать потери данных при удалении видов в общих моделях, в предупреждении содержится дополнительная информация о способе восстановления удаленного вида. На новой главной странице Revit доступно больше способов просмотра, сортировки и поиска моделей и версий. Навигация: перемещение по структуре папок проектов. Выбранная папка будет запоминаться для всех сеансов Revit. Виды: для страниц «Последние» и «Проекты Autodesk» доступны виды сетки и списка.
На виде сетки страницы «Проекты Autodesk» отображаются миниатюры облачных моделей, значки всех типов моделей с совместным доступом или без него , статус публикации со значками, а также доступны функции навигации по проекту и структуре папок. Поиск: на страницах «Последние» и «Проекты Autodesk» можно выполнять фильтрацию, упорядочивание и поиск проектов или моделей. При поиске по проектам Autodesk на странице результатов отображаются все проекты, соответствующие поисковому запросу в рамках хабов, и модели, соответствующие поисковому запросу в текущем проекте. Извлечение: на странице «Последние» можно закрепить основные модели, чтобы они отображались постоянно. Поля: на странице «Проекты Autodesk» добавлены поля «Размер» и «Описание». На виде списка можно настроить отображение или скрытие полей и изменить их порядок. Видимость проекта: функция видимости, которая позволяет отобразить проекты из всех версий Revit. Проекты, созданные не в текущей версии Revit, будут отображаться в состоянии «Отключено».
Эту функцию можно включить или отключить. Чтобы включить ее, в диалоговом окне «Параметры» «Облачная модель» «Видимость проекта» установите флажок «Показывать проекты во всех версиях Revit на главной странице». Можно выполнять поиск по проектам во всех версиях в рамках хабов и отображать их на странице результатов поиска. Сортировка параметров по буквам и цифрам! Параметры проекта можно сортировать по буквам и цифрам на палитре свойств и в диалоговом окне «Свойства типа». Функция «Добавить линию границы зоны» в редакторе группы моделей! Для изменения границ зон в редакторе группы моделей появился инструмент «Добавить линию границы зоны». Выберите вкладку «Архитектура»панель «Помещения и зоны»раскрывающийся список «Зона» Линия границы зоны и нарисуйте границу с помощью инструментов на панели «Рисование».
Выберите границу зоны. Перейдите на вкладку «Архитектура»панель «Модель»раскрывающийся список «Группа модели» Создать группу. В диалоговом окне «Создать группу модели» укажите имя группы, установите флажок «Открыть в редакторе групп» и нажмите «ОК».
Populate schedules, sheets, and views and calculate material quantities. Cut, fill, join, and run phasing scenarios. Use the design-to-documentation engine of Revit to save time and improve design quality when modeling landscape and site conditions.
Improved concrete detailing tools Structural engineers and rebar detailers have new capabilities for creating, scheduling, and documenting rebar. Use the new bar bending details to: Create reinforcement drawings and schedules with detailed fabrication instructions. With this new tool in Revit, when the model changes, the details adapt along with it. Add and customize rebar bending details so that your views and sheets respect your typical practice. Reduce errors and omissions in your document sets.
Навигация: перемещение по структуре папок проектов. Выбранная папка будет запоминаться для всех сеансов Revit. Виды: для страниц «Последние» и «Проекты Autodesk» доступны виды сетки и списка. На виде сетки страницы «Проекты Autodesk» отображаются миниатюры облачных моделей, значки всех типов моделей с совместным доступом или без него , статус публикации со значками, а также доступны функции навигации по проекту и структуре папок. Поиск: на страницах «Последние» и «Проекты Autodesk» можно выполнять фильтрацию, упорядочивание и поиск проектов или моделей. При поиске по проектам Autodesk на странице результатов отображаются все проекты, соответствующие поисковому запросу в рамках хабов, и модели, соответствующие поисковому запросу в текущем проекте. Извлечение: на странице «Последние» можно закрепить основные модели, чтобы они отображались постоянно. Поля: на странице «Проекты Autodesk» добавлены поля «Размер» и «Описание». На виде списка можно настроить отображение или скрытие полей и изменить их порядок. Видимость проекта: функция видимости, которая позволяет отобразить проекты из всех версий Revit. Проекты, созданные не в текущей версии Revit, будут отображаться в состоянии «Отключено». Эту функцию можно включить или отключить. Чтобы включить ее, в диалоговом окне «Параметры» «Облачная модель» «Видимость проекта» установите флажок «Показывать проекты во всех версиях Revit на главной странице». Можно выполнять поиск по проектам во всех версиях в рамках хабов и отображать их на странице результатов поиска. Сортировка параметров по буквам и цифрам! Параметры проекта можно сортировать по буквам и цифрам на палитре свойств и в диалоговом окне «Свойства типа». Функция «Добавить линию границы зоны» в редакторе группы моделей! Для изменения границ зон в редакторе группы моделей появился инструмент «Добавить линию границы зоны». Выберите вкладку «Архитектура»панель «Помещения и зоны»раскрывающийся список «Зона» Линия границы зоны и нарисуйте границу с помощью инструментов на панели «Рисование». Выберите границу зоны. Перейдите на вкладку «Архитектура»панель «Модель»раскрывающийся список «Группа модели» Создать группу. В диалоговом окне «Создать группу модели» укажите имя группы, установите флажок «Открыть в редакторе групп» и нажмите «ОК». В редакторе групп нажмите Добавить. Выберите вкладку «Архитектура»панель «Помещения и зоны»раскрывающийся список «Зона» Линия границы зоны , нарисуйте границу с помощью инструментов на панели «Рисование» и используйте инструмент «Линия» на панели «Рисование», чтобы изменить границу зоны. В редакторе групп нажмите Готово. Сохранение настройки разделителя свойств типа! Ширина столбца, заданная в диалоговом окне «Свойства типа», сохраняется для каждого компьютера. При создании аналога используется корректный инструмент рисования!
To turn it on, you will need to navigate to the File tab in the upper right and then select the Options button. There is a new tab in this property box named Colors. In this tab, you will be able to set Dark Theme or Light Theme with the dropdown. The rest of the colors can be customized in each theme using RGB colors. Add Multiple Views and Schedules You have always been able to drag one view from Project Browser to a Sheet, but now Revit has added the ability to do multiple at a time. Once you have all the views selected, you can drag them into the sheet. You can also do this from the View tab by selecting the View icon, which will open a window that will also allow you to select multiple views at a time. Both of these buttons have an arrow for additional options.